產品特點：

　　缺料報警( 不會干料斗 )，卷長報警( 到指定米數或重量卸軸 )，換網報警( 產量低于此值時提醒換網 )，牽引故障報警( 牽引故障停機 )，漏料不均( 主機皮帶打滑或有故障 )，系統控制穩定精度高、適應性強，簡單易學幾分鐘就會，觸摸屏顯示清晰直觀。擠塑行業已應用于純料、各種再生料、加填充料及粉末狀料。

　　PRODUCT FEATURES：

　　Lack of material alarm (not dry hopper), long coil alarm (to specified meters or weight unload), net change alarm (when output is below this setting),take up fault alarm (take up failure stop),Uneven leakage (main belt slip or fault), system control stability,high precision,strong adaptability, easy to learn,touch screen display clear and intuitive.Extrusion industry has been used in pure materials, all kinds of recycled materials, filling materials and powder materials.

　　產品優點：

　　1)節省勞動力：工人不必再去抽查米克重，不必?fù)?dān)心干料斗平時就等著報警填料就可以了。

　　2)提高產品質量，提高競爭力：由此系統吹的膜純料明顯整體平整度會好很多，再生料克重相當準，客戶都難以想到吹出的膜會這么好，滿意度提升至 100%。

　　3)老板松心：不必再為吹出的膜薄或厚，交貨時發愁了。

　　4)降低對工人的標準：克重控制對工人干的時間長短和經驗掌握要求很高。

　　5)節省原料：此系統一般開機后會在 2 秒鐘開始調節，1 分鐘左右調節到規定值，無須等工人把機器開好泡調好再測量克重再調節牽引，可節約幾公斤無用的料，因吹膜機經常需要停機換網所以長期計算節省很多。( 平時經常抽袋測量浪費很多 )

　　PRODUCT BENEFITS:

　　1) Labor savings:workers do not have to spot check the Mick weight, do not worry about dry material hopper usually waiting for the alarm filler can be.

　　2) improve the quality of the product and improve the competitiveness: the film pure material blown by this system will be much better.the weight of the recycled material is quite accurate, the customers can hardly imagine that the blown-out film will be so good, and the satisfaction will be increased to100%.

　　3) loosening of the plate: there is no need to worry about the final delivery of blown thin or thick membranes.

　　4) reduce the standard for workers: heavy control requires a great deal of work time and experience.

　　5) Save raw materials: the system will normally start adjusting in 2 seconds after it is turned on, and it will be adjusted to the specified value in about 1 minute. There is no need to wait for the workers to adjust the machine well and then measure the weight and re-adjust the traction, can save a few kilograms of useless material, because the film blower often needs to shut down to change the net so long-term calculation saving a lot.(a lot of wasteful measurements are usually taken out of the bag.)